1 /*
2 * include/asm-i386/serial.h
3 */
4
5 #include <linux/config.h>
6
7 /*
8 * This assumes you have a 1.8432 MHz clock for your UART.
9 *
10 * It'd be nice if someone built a serial card with a 24.576 MHz
11 * clock, since the 16550A is capable of handling a top speed of 1.5
12 * megabits/second; but this requires the faster clock.
13 */
14 #define BASE_BAUD ( 1843200 / 16 )
15
16 /* Standard COM flags (except for COM4, because of the 8514 problem) */
17 #ifdef CONFIG_SERIAL_DETECT_IRQ
18 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
19 #define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
20 #else
21 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
22 #define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
23 #endif
24
25 #ifdef CONFIG_SERIAL_MANY_PORTS
26 #define FOURPORT_FLAGS ASYNC_FOURPORT
27 #define ACCENT_FLAGS 0
28 #define BOCA_FLAGS 0
29 #define HUB6_FLAGS 0
30 #endif
31
32 #define MCA_COM_FLAGS (STD_COM_FLAGS|ASYNC_BOOT_ONLYMCA)
33
34 /*
35 * The following define the access methods for the HUB6 card. All
36 * access is through two ports for all 24 possible chips. The card is
37 * selected through the high 2 bits, the port on that card with the
38 * "middle" 3 bits, and the register on that port with the bottom
39 * 3 bits.
40 *
41 * While the access port and interrupt is configurable, the default
42 * port locations are 0x302 for the port control register, and 0x303
43 * for the data read/write register. Normally, the interrupt is at irq3
44 * but can be anything from 3 to 7 inclusive. Note that using 3 will
45 * require disabling com2.
46 */
47
48 #define C_P(card,port) (((card)<<6|(port)<<3) + 1)
49
50 #define STD_SERIAL_PORT_DEFNS \
51 /* UART CLK PORT IRQ FLAGS */ \
52 { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
53 { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
54 { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
55 { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
56
57
58 #ifdef CONFIG_SERIAL_MANY_PORTS
59 #define EXTRA_SERIAL_PORT_DEFNS \
60 { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
61 { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
62 { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
63 { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
64 { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
65 { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
66 { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
67 { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
68 { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
69 { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
70 { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
71 { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
72 { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
73 { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
74 { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
75 { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
76 { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
77 { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
78 { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
79 { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
80 { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
81 { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
82 { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
83 { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
84 { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
85 { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
86 { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
87 { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
88 #else
89 #define EXTRA_SERIAL_PORT_DEFNS
90 #endif
91
92 /* You can have up to four HUB6's in the system, but I've only
93 * included two cards here for a total of twelve ports.
94 */
95 #if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
96 #define HUB6_SERIAL_PORT_DFNS \
97 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
98 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
99 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
100 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
101 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
102 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
103 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
104 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
105 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
106 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
107 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
108 { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
109 #else
110 #define HUB6_SERIAL_PORT_DFNS
111 #endif
112
113 #ifdef CONFIG_MCA
114 #define MCA_SERIAL_PORT_DFNS \
115 { 0, BASE_BAUD, 0x3220, 3, MCA_COM_FLAGS }, \
116 { 0, BASE_BAUD, 0x3228, 3, MCA_COM_FLAGS }, \
117 { 0, BASE_BAUD, 0x4220, 3, MCA_COM_FLAGS }, \
118 { 0, BASE_BAUD, 0x4228, 3, MCA_COM_FLAGS }, \
119 { 0, BASE_BAUD, 0x5220, 3, MCA_COM_FLAGS }, \
120 { 0, BASE_BAUD, 0x5228, 3, MCA_COM_FLAGS },
121 #else
122 #define MCA_SERIAL_PORT_DFNS
123 #endif
124
125 #define SERIAL_PORT_DFNS \
126 STD_SERIAL_PORT_DEFNS \
127 EXTRA_SERIAL_PORT_DEFNS \
128 HUB6_SERIAL_PORT_DFNS \
129 MCA_SERIAL_PORT_DFNS
130
131
|
This page was automatically generated by the
LXR engine.
|