Linux kernel & device driver programming

Cross-Referenced Linux and Device Driver Code

[ source navigation ] [ diff markup ] [ identifier search ] [ freetext search ] [ file search ]
Version: [ 2.6.11.8 ] [ 2.6.25 ] [ 2.6.25.8 ] [ 2.6.31.13 ] Architecture: [ i386 ]
  1 #ifndef _LINUX_XD_H
  2 #define _LINUX_XD_H
  3 
  4 /*
  5  * This file contains the definitions for the IO ports and errors etc. for XT hard disk controllers (at least the DTC 5150X).
  6  *
  7  * Author: Pat Mackinlay, pat@it.com.au
  8  * Date: 29/09/92
  9  *
 10  * Revised: 01/01/93, ...
 11  *
 12  * Ref: DTC 5150X Controller Specification (thanks to Kevin Fowler, kevinf@agora.rain.com)
 13  * Also thanks to: Salvador Abreu, Dave Thaler, Risto Kankkunen and Wim Van Dorst.
 14  */
 15 
 16 #include <linux/interrupt.h>
 17 
 18 /* XT hard disk controller registers */
 19 #define XD_DATA         (xd_iobase + 0x00)      /* data RW register */
 20 #define XD_RESET        (xd_iobase + 0x01)      /* reset WO register */
 21 #define XD_STATUS       (xd_iobase + 0x01)      /* status RO register */
 22 #define XD_SELECT       (xd_iobase + 0x02)      /* select WO register */
 23 #define XD_JUMPER       (xd_iobase + 0x02)      /* jumper RO register */
 24 #define XD_CONTROL      (xd_iobase + 0x03)      /* DMAE/INTE WO register */
 25 #define XD_RESERVED     (xd_iobase + 0x03)      /* reserved */
 26 
 27 /* XT hard disk controller commands (incomplete list) */
 28 #define CMD_TESTREADY   0x00    /* test drive ready */
 29 #define CMD_RECALIBRATE 0x01    /* recalibrate drive */
 30 #define CMD_SENSE       0x03    /* request sense */
 31 #define CMD_FORMATDRV   0x04    /* format drive */
 32 #define CMD_VERIFY      0x05    /* read verify */
 33 #define CMD_FORMATTRK   0x06    /* format track */
 34 #define CMD_FORMATBAD   0x07    /* format bad track */
 35 #define CMD_READ        0x08    /* read */
 36 #define CMD_WRITE       0x0A    /* write */
 37 #define CMD_SEEK        0x0B    /* seek */
 38 
 39 /* Controller specific commands */
 40 #define CMD_DTCSETPARAM 0x0C    /* set drive parameters (DTC 5150X & CX only?) */
 41 #define CMD_DTCGETECC   0x0D    /* get ecc error length (DTC 5150X only?) */
 42 #define CMD_DTCREADBUF  0x0E    /* read sector buffer (DTC 5150X only?) */
 43 #define CMD_DTCWRITEBUF 0x0F    /* write sector buffer (DTC 5150X only?) */
 44 #define CMD_DTCREMAPTRK 0x11    /* assign alternate track (DTC 5150X only?) */
 45 #define CMD_DTCGETPARAM 0xFB    /* get drive parameters (DTC 5150X only?) */
 46 #define CMD_DTCSETSTEP  0xFC    /* set step rate (DTC 5150X only?) */
 47 #define CMD_DTCSETGEOM  0xFE    /* set geometry data (DTC 5150X only?) */
 48 #define CMD_DTCGETGEOM  0xFF    /* get geometry data (DTC 5150X only?) */
 49 #define CMD_ST11GETGEOM 0xF8    /* get geometry data (Seagate ST11R/M only?) */
 50 #define CMD_WDSETPARAM  0x0C    /* set drive parameters (WD 1004A27X only?) */
 51 #define CMD_XBSETPARAM  0x0C    /* set drive parameters (XEBEC only?) */
 52 
 53 /* Bits for command status byte */
 54 #define CSB_ERROR       0x02    /* error */
 55 #define CSB_LUN         0x20    /* logical Unit Number */
 56 
 57 /* XT hard disk controller status bits */
 58 #define STAT_READY      0x01    /* controller is ready */
 59 #define STAT_INPUT      0x02    /* data flowing from controller to host */
 60 #define STAT_COMMAND    0x04    /* controller in command phase */
 61 #define STAT_SELECT     0x08    /* controller is selected */
 62 #define STAT_REQUEST    0x10    /* controller requesting data */
 63 #define STAT_INTERRUPT  0x20    /* controller requesting interrupt */
 64 
 65 /* XT hard disk controller control bits */
 66 #define PIO_MODE        0x00    /* control bits to set for PIO */
 67 #define DMA_MODE        0x03    /* control bits to set for DMA & interrupt */
 68 
 69 #define XD_MAXDRIVES    2       /* maximum 2 drives */
 70 #define XD_TIMEOUT      HZ      /* 1 second timeout */
 71 #define XD_RETRIES      4       /* maximum 4 retries */
 72 
 73 #undef DEBUG                    /* define for debugging output */
 74 
 75 #ifdef DEBUG
 76         #define DEBUG_STARTUP   /* debug driver initialisation */
 77         #define DEBUG_OVERRIDE  /* debug override geometry detection */
 78         #define DEBUG_READWRITE /* debug each read/write command */
 79         #define DEBUG_OTHER     /* debug misc. interrupt/DMA stuff */
 80         #define DEBUG_COMMAND   /* debug each controller command */
 81 #endif /* DEBUG */
 82 
 83 /* this structure defines the XT drives and their types */
 84 typedef struct {
 85         u_char heads;
 86         u_short cylinders;
 87         u_char sectors;
 88         u_char control;
 89         int unit;
 90 } XD_INFO;
 91 
 92 /* this structure defines a ROM BIOS signature */
 93 typedef struct {
 94         unsigned int offset;
 95         const char *string;
 96         void (*init_controller)(unsigned int address);
 97         void (*init_drive)(u_char drive);
 98         const char *name;
 99 } XD_SIGNATURE;
100 
101 #ifndef MODULE
102 static int xd_manual_geo_init (char *command);
103 #endif /* MODULE */
104 static u_char xd_detect (u_char *controller, unsigned int *address);
105 static u_char xd_initdrives (void (*init_drive)(u_char drive));
106 
107 static void do_xd_request (struct request_queue * q);
108 static int xd_ioctl (struct block_device *bdev,fmode_t mode,unsigned int cmd,unsigned long arg);
109 static int xd_readwrite (u_char operation,XD_INFO *disk,char *buffer,u_int block,u_int count);
110 static void xd_recalibrate (u_char drive);
111 
112 static irqreturn_t xd_interrupt_handler(int irq, void *dev_id);
113 static u_char xd_setup_dma (u_char opcode,u_char *buffer,u_int count);
114 static u_char *xd_build (u_char *cmdblk,u_char command,u_char drive,u_char head,u_short cylinder,u_char sector,u_char count,u_char control);
115 static void xd_watchdog (unsigned long unused);
116 static inline u_char xd_waitport (u_short port,u_char flags,u_char mask,u_long timeout);
117 static u_int xd_command (u_char *command,u_char mode,u_char *indata,u_char *outdata,u_char *sense,u_long timeout);
118 
119 /* card specific setup and geometry gathering code */
120 static void xd_dtc_init_controller (unsigned int address);
121 static void xd_dtc5150cx_init_drive (u_char drive);
122 static void xd_dtc_init_drive (u_char drive);
123 static void xd_wd_init_controller (unsigned int address);
124 static void xd_wd_init_drive (u_char drive);
125 static void xd_seagate_init_controller (unsigned int address);
126 static void xd_seagate_init_drive (u_char drive);
127 static void xd_omti_init_controller (unsigned int address);
128 static void xd_omti_init_drive (u_char drive);
129 static void xd_xebec_init_controller (unsigned int address);
130 static void xd_xebec_init_drive (u_char drive);
131 static void xd_setparam (u_char command,u_char drive,u_char heads,u_short cylinders,u_short rwrite,u_short wprecomp,u_char ecc);
132 static void xd_override_init_drive (u_char drive);
133 
134 #endif /* _LINUX_XD_H */
135 
  This page was automatically generated by the LXR engine.